| Technical data |
Standard |
Unit |
PA 6 G |
Oilamid® |
Calaumid®
612 |
Calaumid®
1200 |
PA 6 |
PA 66 |
POM |
PET |
PET GL |
| Mechanical properties |
|
|
|
|
|
|
|
|
|
|
|
| Density |
DIN 53 479 |
g/cm3 |
1,15 |
1,14 |
1,12 |
1,03 |
1,14 |
1,14 |
1,41 |
1,38 |
1,43 |
Tensile strength
(short duration) |
DIN 53 455 |
MPa |
80 |
80 |
80 |
60 |
70 |
85 |
65 |
80 |
75 |
Modulus of elasticity
in flexure
(short duration) |
DIN 53 457 |
MPa |
3.400 |
2.800 |
2.800 |
2.200 |
2.500 |
2.900 |
2.900 |
2.600 |
- |
Modulus of elasticity
in tension
(short duration) |
DIN 53 457 |
MPa |
3.100 |
2.500 |
2.300 |
2.400 |
2.700 |
3.000 |
3.000 |
3.000 |
2.200 |
| Bending strength |
DIN 53 452 |
MPa |
140 |
135 |
135 |
90 |
130 |
135 |
115 |
125 |
- |
| Impact strength |
DIN 53 453 |
kJ/m2 |
n.B. |
n.B |
n.B. |
n. B. |
n.B. |
n. B. |
n. B. |
n. B. |
30 |
| Notch impact strength |
DIN 53 453 |
kJ/m2 |
> 4 |
> 5 |
>12 |
>15 |
>3 |
>3 |
>10 |
>4 |
2 |
Ball indention
hardness H358/30 |
DIN 53 456 |
MPa |
160 |
140 |
140 |
100 |
160 |
170 |
150 |
140 |
- |
Sliding friction
coefficient (dry run) 1) |
- |
- |
0,36 |
0,18 |
0,36 |
0,40 |
0,38 |
0,35 |
0,32 |
0,25 |
0,2 |
| Thermal properties |
|
|
|
|
|
|
|
|
|
|
|
| Melting temperature |
- |
°C |
+ 220 |
+ 220 |
195 |
190 |
+ 218 |
+ 265 |
+ 178 |
+ 255 |
+ 255 |
Coefficient of linear
expansion 2) |
DIN VDE 0304 |
10-5 . K-1 |
7 - 8 |
7 - 8 |
7-8 |
10-11 |
8-9 |
9-10 |
9-10 |
7-8 |
7-8 |
Service temperature
range 3) |
- |
°C |
-40 to
+105 |
-40 to
+105 |
-40 to
+105 |
-60 to
+110 |
-60 to
+100 |
-30 to
+100 |
-30 to
+100 |
-20 to
+100 |
-20 to
+110 |
Max. Service
temperature range 4) |
- |
°C |
+ 170 |
+ 160 |
+ 160 |
+ 150 |
+ 140 |
+ 150 |
+ 140 |
+ 160 |
+ 160 |
| Thermal conductivity |
DIN 52 612 |
W/(K.m) |
0,23 |
0,23 |
0,23 |
0,23 |
0,23 |
0,23 |
0,31 |
0,24 |
0,23 |
| Water absorption |
|
|
|
|
|
|
|
|
|
|
|
Moisture absorption 5)
(maximum) |
DIN 53 715 |
% |
2,2 |
1,8 |
1,9 |
0,9 |
3,0 |
2,5 |
0,2 |
0,25 |
0,2 |
Moisture absorption 6)
(saturated) |
DIN 53 495 |
% |
6,5 |
5,5 |
5,8 |
1,4 |
10,0 |
9,0 |
0,8 |
0,5 |
0,4 |
1) against steel, hardened and ground
P = 0.05 MPa,
V = 0.6 m/sec
t = 40 °C near sliding surface
2) for the temperature range from + 23°C to + 60°C
3) Empirical values with finished components without load in air, depending on type and form of heat application, long term (= months)
4) Empirical values with finished components without load in air, depending on type and form of heat application, short term (= max. 1 h)
5) In normal ambient conditions 23 °C / 50 % RH
6) In water
1 MPa = 1 N/mm2
n. b. = non breaking
Disclaimer:
We cannot anticipate all conditions under which this information and our products, or the products of other manufacturers in combination with our products, may be used. We accept no responsibility for results obtained by the application of this information or the safety and suitability of our products, either alone or in combination with other products. Users are advised to make their own tests to determine the safety and suitability of each such product or product combination for their own purposes. Unless otherwise agreed in writing, Cut To Size Plastics sell the products without warranty and buyers and users assume all responsibility and liability for loss or damage arising from the handling and use of our products, either used alone or in combination with other products.
For the most recent technical data and free application advice, please call Cut To Size Plastics on: (02) 9439 7066.
We expressly reserve the right to make changes to this document. Errors excepted.
|